For Author

Manuscripts should be submitted by one of the authors of the manuscript by filling submit manuscript form or by sending through e-mail. Regardless of the source of the word-processing tool, only electronic PDF (.pdf) or Word (.doc, .Docx, .rtf) files can be submitted through submit manuscript form. There is no page limit. Only online submissions are accepted to facilitate rapid publication and minimize administrative costs. Submissions by anyone other than one of the authors will not be accepted. The submitting author takes responsibility for the paper during submission and peer review. If for some technical reason submission through the SM is not possible, the author can contact contact@scientificsynergy.com  for support.

Terms of Submission:

Papers must be submitted on the understanding that they have not been published elsewhere and are not currently under consideration by another journal published by Eagle Publishing Group or any other publisher. The submitting author is responsible for ensuring that the article’s publication has been approved by all the other co-authors. It is also the author’s responsibility to ensure that the articles emanating from a particular institution are submitted with the approval of the necessary institution. Only an acknowledgment from the editorial office officially establishes the date of receipt. Further correspondence and proofs will be sent to the author(s) before publication unless otherwise indicated. It is a condition of submission of a paper that the authors permit editing of the paper for readability. All enquiries concerning the publication of accepted papers should be addressed to contact@scientificsynergy.com

Peer Review:

All manuscripts are subject to peer review and are expected to meet standards of academic excellence. Submissions will be considered by an editor and “if not rejected right away” by peer-reviewers, whose identities will remain anonymous to the authors.

Units of Measurement:

Units of measurement should be presented simply and concisely using System International (SI) units.

Title and Authorship Information:

The following information should be included:

Paper title

Full author names

Full institutional mailing addresses

Email addresses

Abstract:

The manuscript should contain an abstract. It should contain breif introduction of research and citation-free. Abstract should not exceed 250 words.

 Introduction:

This section should be succinct, with no subheadings.

Materials and Methods:

This part should contain sufficient detail so that all procedures can be repeated. It can be divided into subsections if several methods are described.

Results and Discussion:

This section may each be divided by subheadings or may be combined.

Conclusions:

This should clearly explain the main conclusions of the work highlighting its importance and relevance.

Acknowledgments:

All acknowledgments (if any) should be included at the very end of the paper before the references and may include supporting grants, presentations, and so forth.

References:

Authors are responsible for ensuring that the information in each reference is complete and accurate. All references must be numbered consecutively and citations of references in the text should be identified using numbers in square brackets (e.g., “as discussed by Smith [9]”; “as discussed elsewhere [9, 10]”). All references should be cited within the text; otherwise, these references will be automatically removed.

Preparation of Figures:

Upon submission of an article, authors are supposed to include all figures and tables in the PDF file of the manuscript. Figures and tables should not be submitted in separate files. If the article is accepted, authors will be asked to provide the source files of the figures. Each figure should be supplied in a separate electronic file. All figures should be cited in the paper in a consecutive order. Figures should be supplied in either vector art formats (Illustrator, EPS, WMF, FreeHand, CorelDraw, PowerPoint, Excel, etc.) or bitmap formats (Photoshop, TIFF, GIF, JPEG, etc.). Bitmap images should be of 300 dpi resolution at least, unless the resolution is intentionally set to a lower level for scientific reasons. If a bitmap image has labels, the image and labels should be embedded in separate layers.

Preparation of Tables:

Tables should be cited consecutively in the text. Every table must have a descriptive title and if numerical measurements are given, the units should be included in the column heading. Vertical rules should not be used.

Proofs:

Corrected proofs must be returned to the publisher within 2-3 days of receipt. The publisher will do everything possible to ensure prompt publication. It will therefore be appreciated if the manuscripts and figures conform from the outset to the style of the journal.

To Submit your Manuscript Click Here or email: contact@scientificsynery.com